Vehicles
Sections
214 not categorized PORSCHE 930 BUSHINGSCan't find what you need? Try browsing the Accessories or Exploded Diagrams!Filtered by: 968 1992-95 (includes uncategorized and accessory items) FVD33300905ATK Send us your original spring plate and we will have it reconditioned for you. The reconditioning process includes full inspection to ensure proper operation after the remanufacturing process. We then disassemble, degrease and media blast the part. Once fully prepared, we install new rs spec. (85 shore) rubber bushings/bearings. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Then we seal the spring plate with a corrosion resistant plating. Sold individually. 2 necessary per car. Please note: this does not fit cars with the g50 transmission.
$312.40
Make a selection FVD33391101SET These bushings are manufactured from higher density, rs specification rubber (85 shore). Rs bushings are more durable than OEM 65 shore, provide more positive suspension location and are still quiet and compliant for street use. This set is a direct replacement for original part # 911 333 009 00 sold as a set. 1 necessary per axle.
$108.90
Make a selection
From $15.00
Make a selection FVD33300905 This rear spring plate is manufactured to the highest of European standards to ensure the quality and performance you expect for your Porsche. New rs spec. (85 shore) rubber bushings are installed to make this a direct bolt on. 85 shore rubber is more durable than OEM 65 shore and provides more positive suspension location yet is still quiet and compliant for street use. Features: made from ¼ inch spring steel includes new rs spec. (85 shore) rubber bushings made in Germany sold individually. 2 necessary per car.
$273.90
Make a selection FVD0599249441
$56.10
Make a selection FVD37504332R Replace the worn-out, original soft rubber engine mounts with our higher density, rs specification rubber bushings. These are manufactured of rubber with an 85-shore hardness value. 85-shore is the same density as what is used in the rs models. It is more durable, provides more positive, sharper shifts and offers crisper throttle response. Yet, rs spec rubber is still quiet and comfortable for street use. Features: sharper shifts crisper throttle response does not produce nvh (noise vibration harshness) like teflon or solid bushings. Rubber has a shore hardness value of 85 (like rs models) made in Germany sold as a set. 1 necessary per car.
$152.90
Make a selection FVD3419991 This is a cost effective alternative to buying new control arms. Replace worn-out original soft rubber (65 shore hardness value) control arm bushings with new bushings of the same rubber (65 shore hardness value). This bushing set is made in Germany, weather sealed, crafted in high carbon steel and 7075 t6 aircraft aluminum and includes a 65 shore hardness value cores. This is a front and rear bushing for the front lower control arm (wishbone). 2 sets are necessary per car.
$124.30
Make a selection
$315.87
Make a selection
$30.80
Make a selection
$307.70
Make a selection
$48.18
Make a selection
$46.20
Make a selection 95134104100 General Fitment944 1985-88944 1989-91 968 1992-95
From $78.98
Make a selection
$75.59
Make a selection 012301183A
$2.94
Make a selection
$188.55
Make a selection 088311533
$5.84
Make a selection P904785 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1989-91 944 1985-88 944 1982-85 968 1992-95
$375.00
Make a selection 93110211100 High-quality OEM (original equipment manufacturer) fag replacement, designed to perform like the original. We source this part in Germany to ensure quality, reliability and precise fitment. Flywheel bushing located in the center of the flywheel at the rear of the crankshaft. View/Change Diagram
From $7.98
Make a selection FVD424041 Ok, we know you are a driving enthusiast if you are shopping for a short shifter for your manual transmission. Driving enthusiasts appreciate a more direct connection to the car, transmission and road surface. If you are trying to clean up those long shifts and side to side play on the factory shifter you are certainly on the right track with this upgrade. This numeric racing short shift kit uses precision ball bearings on all axis' which produce 35% shorter throws with an almost gated like action. Short gated like throws increase your driving experience by enhancing a more direct, mechanical connection to your car. Once installed you will find joy with every shift and this will easily become one of your favor...(choose a part on the right to read more)
$808.50
Make a selection P904784 Forged from the highest quality steel, each torsion bar is centerlessly ground to provide a constant spring rate, chemically coated to protect against rust and then matched in pair sets to ensure that both sides of the car are equally suspended. All performance products torsion bars are guaranteed for 3 years against breakage. Note: worn torsion bar bushings will shorten the life of torsion bars. Our 3-year guarantee will remain valid only when bushings are in good condition at time of installing new torsion bars. Sold in pairs. General Fitment924 1976-79924 1980-85 924 1986-88 944 1982-85 944 1985-88 944 1989-91 968 1992-95
$347.95
Make a selection © 2024 Automobile Atlanta Inc. 505 S. Marietta Pkwy • Marietta, GA 30060 • Order By Phone: 800 792 4944 770 427 2844 |